FPGA挂载NVME SSD(二) | 您所在的位置:网站首页 › linux nvme挂载 › FPGA挂载NVME SSD(二) |
1. 首先要在Ubuntu下安装Petalinux 2017.2 2. 设置Petalinux 环境变量 source //settings.sh 3. 新建目录~/projets/fpga-drive-aximm-pcie 4. 把Windows下的Vivado工程复制到~/projets/fpga-drive-aximm-pcie下 5. 新建Petalinux工程 petalinux-create --type project --template zynq --name petalinux_prj 6. 切换到petalinux_prj目录 cd petalinux_prj/ 7. 导入HDF petalinux-config --get-hw-description ../fpga-drive-aximm-pcie-2017v2_hpc/Vivado/zc706_hpc_pcie/zc706_hpc_pcie.sdk/ 随之弹出Linux System Configuration界面,不做任何更改,保存退出 8. 配置内核 petalinux-config -c kernel Check: Bus options->PCI support should already be enabled by default Check: Bus options->PCI support->Message Signaled Interrupts (MSI and MSI-X) should already be enabled by default Check: Bus options->PCI support->Enable PCI resource re-allocation detection should already be enabled by default Check: Bus options->PCI support->PCI host controller drivers->Xilinx AXI PCIe host bridge support should already be enabled by default Enable: Device Drivers->Block devices->NVM Express block device 9. 配置根文件系统 petalinux-config -c rootfs Configure the root file system to include some utilities we will need to setup the NVMe PCIe SSD: Enable PCI utils (for lspci): Filesystem Packages->console/utils->pciutils->pciutils Enable required packages for lsblk, fdisk, mkfs, blkid: [ ] Filesystem Packages->base->util-linux->util-linux Filesystem Packages->base->util-linux->util-linux-blkid Filesystem Packages->base->util-linux->util-linux-fdisk Filesystem Packages->base->util-linux->util-linux-mkfs Filesystem Packages->base->util-linux->util-linux-mount Filesystem Packages->base->e2fsprogs->e2fsprogs Filesystem Packages->base->e2fsprogs->e2fsprogs-mke2fs 10. 编译 petalinux-build 11. 打包并通过JTAG启动 petalinux-package --boot --fsbl ./images/linux/zynq_fsbl.elf --fpga ../fpga-drive-aximm-pcie-2017v2_hpc/Vivado/zc706_hpc_pcie/zc706_hpc_pcie.runs/impl_1/zc706_hpc_pcie_wrapper.bit --uboot --force petalinux-package --prebuilt --fpga ../fpga-drive-aximm-pcie-2017v2_hpc/Vivado/zc706_hpc_pcie/zc706_hpc_pcie.runs/impl_1/zc706_hpc_pcie_wrapper.bit petalinux-boot --jtag --prebuilt 3 --fpga --bitstream ../fpga-drive-aximm-pcie-2017v2_hpc/Vivado/zc706_hpc_pcie/zc706_hpc_pcie.runs/impl_1/zc706_hpc_pcie_wrapper.bit 不过我的JTAG启动不成功,懒得折腾了,把/petalinux_prj/images/linux目录下的image.ub, zynq_fsbl.elf, u-boot.elf和zc706_hpc_pcie_wrapper.bit拷贝到Windows下,将zynq_fsbl.elf, u-boot.elf和zc706_hpc_pcie_wrapper.bit生成BOOT.BIN,最后将BOOT.BIN和image.ub放到SD卡,上电启动 后续测试详细添加链接描述 对SSD进行分区,并在SSD中新建.txt文件,并进行读写。 文章转载自: https://blog.csdn.net/zkf0100007/article/details/84197247 |
CopyRight 2018-2019 实验室设备网 版权所有 |